3 Wire PT100 Connection Diagram: Pinout Guide (2026)
A 3 wire pt100 connection diagram uses two identical-colored wires (typically red) connected to one side of the RTD element and a single different-colored wire (typically white) connected to the opposite side. The two common red wires compensate for lead wire resistance across the transmitter’s internal Wheatstone bridge, ensuring accurate temperature measurement.
📌 Key Takeaways
- A 3-wire PT100 RTD uses 100 ohms platinum resistance at 0°C with an alpha coefficient of 0.00385 Ω/Ω/°C.
- Standard IEC 60751 wire color code designates two red wires for the sense loop and one white wire for the signal path.
- Maintain lead wire impedance resistance matched below 0.1 ohms between paired identical conductors to prevent temperature drift.
- Swapping the single signal lead (white) with one of the excitation sense leads (red) causes extreme temperature offset errors.
- Use 24 AWG to 18 AWG shielded twisted-pair wiring for high noise immunity; consult an instrument technician for transmitter recalibration.
Accurate temperature measurement in high-performance automotive dynos, engine telemetry, and industrial process automation relies heavily on Resistance Temperature Detectors (RTDs). Among these, the 3-wire Pt100 sensor is the industry standard for balancing measurement accuracy with cost efficiency. Implementing an accurate 3 wire pt100 connection diagram is critical for eliminating lead wire resistance errors that would otherwise corrupt real-time temperature telemetry. This technical wiring guide breaks down standard wire color codes, terminal block pin assignments, lead compensation mechanics, and wiring sequences to ensure precise, drift-free temperature measurements across your control modules.

Standard Wire Color Code Chart for 3 Wire Pt100 Sensors
According to OEM specs and international standards such as IEC 60751 / DIN EN 60751, a 3-wire Pt100 sensor utilizes two distinct color-coded circuits: a single primary excitation lead (often referred to as the hot wire lead) and a pair of common return leads (neutral wire and compensation lines). While the IEC 60751 standard specifies Red for the single element lead and White for the common return pair, legacy automotive and North American industrial systems may follow alternate wiring conventions.
| Standard System | Wire Color Code | Pin Assignment / Terminals | Function & Description |
|---|---|---|---|
| IEC 60751 (Standard) | Red (1 Lead) White (2 Leads) |
Terminal 1: Red (S+) Terminal 2: White (S-) Terminal 3: White (COMP) |
Red delivers constant excitation voltage/current; Dual White leads form the compensation loop. |
| ANSI MC96.1 (US) | Red (1 Lead) Black (2 Leads) |
Terminal A: Red Terminal B: Black Terminal C: Black |
Common in older domestic industrial transmitters and custom automotive harness builds. |
| DIN 43760 (Legacy German) | White (1 Lead) Red (2 Leads) |
Terminal 1: White Terminal 2: Red Terminal 3: Red |
Found in European vintage machinery and legacy automotive test cell installations. |
| Shield Cable Drain | Bare / Green-Yellow Wire | Chassis Earth / Ground Terminal | Dedicated ground wire shield drain to eliminate electromagnetic interference (EMI). |
Always verify lead resistance before landing wires on your terminal block. Between the two same-color wires (e.g., White to White), a digital multimeter (DMM) should register near 0.0 Ω to 0.5 Ω. Between a primary wire (Red) and any common wire (White), the DMM must read approximately 100.0 Ω at 0°C (32°F) or ~108.4 Ω at standard room temperature (21°C / 70°F).
Understanding the 3 Wire Pt100 Connection Diagram Mechanics

The standard Pt100 sensor is a platinum RTD that exhibits a baseline resistance of 100 Ohms at 0°C with a positive temperature coefficient ($\alpha = 0.003851 \, \Omega/\Omega/^\circ\text{C}$). In a basic 2-wire arrangement, the copper lead resistance of the harness is added directly in series with the platinum element resistance. A cable run of 50 feet using 22 AWG copper wire adds roughly 1.6 Ohms of total lead resistance. In a Pt100 circuit, an uncompensated 1.6 Ohm error translates to a massive false temperature elevation of approximately 4°C (7.2°F).
The 3 wire pt100 connection diagram solves this vulnerability by adding a third conductor to construct a balanced bridge circuit or differential operational amplifier input. As illustrated in the diagram above, the 3-wire topology splits the circuit into two distinct measurement legs:
- Leg 1 (Primary Circuit): Pass current from the controller’s constant excitation current source through Lead 1 (Red) and the Pt100 platinum resistor element, returning through Lead 2 (White). The controller reads $V_{\text{total}} = V_{\text{element}} + V_{\text{Lead1}} + V_{\text{Lead2}}$.
- Leg 2 (Compensation Loop): Pass the same current or sense voltage across Lead 2 (White) and Lead 3 (White). Because no active sense current flows down Lead 3 into the element, the voltage dropped across Lead 3 measures purely $V_{\text{Lead2}} + V_{\text{Lead3}}$.
Assuming all three conductors match in wire gauge, length, and temperature environment, $V_{\text{Lead1}} = V_{\text{Lead2}} = V_{\text{Lead3}}$. The instrumentation circuit subtracts the voltage measured across the compensation loop from the primary measurement loop. This cancels out line resistance dynamically, leaving only the precise voltage drop across the 100-ohm RTD sensing element.
How to Wire a 3 Wire Pt100 Connection Diagram to Control Modules

Follow this systematic procedure to complete a clean, robust installation of your 3-wire RTD sensor into a Programmable Logic Controller (PLC), temperature transmitter, or engine control unit (ECU) telemetry module.
- Prepare Cable Insulation and Conductors: Strip the outer protective jacket back approximately 1.5 inches (38 mm), taking care not to nick the interior wire insulation or the braided shield wire. Strip 0.25 inches (6 mm) of insulation from the Red, White 1, and White 2 conductors. Crimp insulated bootlace ferrules onto each stranded wire end to prevent loose strands from shorting adjacent terminals on high-density terminal blocks.
- Identify Controller Terminal Block Layout: Examine the pin assignment diagram on your temperature controller or 4-20mA transmitter. Common designations include:
- Terminal A / RL1 / S+ : Excitation Current Source (+)
- Terminal B / RL2 / S- : Sensor Signal Return (-)
- Terminal C / COMP / b : Lead Wire Resistance Compensation Input
- Land the Primary Excitation Lead: Connect the solid Red wire (or the single-color primary hot wire) to Terminal A (S+). Torque the screw clamp on the terminal block to 0.4–0.5 Nm (3.5–4.4 in-lbs).
- Land the Common Return Leads: Land the first White lead (neutral wire return line) into Terminal B (S-). Land the second White lead (compensation wire) into Terminal C (COMP / b). Because both White wires connect internally to the exact same side of the Pt100 element, their pin assignment order on Terminals B and C is fully interchangeable.
- Terminate the Ground Wire Shield: Connect the outer drain shield braided ground wire to the designated Earth Ground terminal block on the controller chassis. Connect the ground wire on the transmitter/controller end only to avoid creating ground loops. Trim and isolate the shield ground wire at the sensor end using heat-shrink tubing.
Never apply external power supply voltages (12V, 24V DC, or 120V AC) directly across any 3-wire Pt100 terminals. RTD inputs utilize millivolt-level excitation current (typically 0.1 mA to 1.0 mA). Applying standard system line voltage will instantly destroy the platinum thin-film element and burn out delicate controller analog-to-digital converter (ADC) channels.
Signal Voltage, Excitation Current, and Wire Gauge Specifications
Designing and installing reliable RTD instrumentation circuits requires strict adherence to electrical tolerances and conductor geometry specs. Standard specifications for automotive dyno cells and industrial transmitters specify the operational parameters detailed below.
Excitation Current: 0.1 mA to 1.0 mA DC maximum (1.0 mA limit prevents self-heating errors).
Maximum Allowable Cable Resistance: 20 Ω to 50 Ω per individual lead run (varies by controller).
Recommended Wire Gauge: 22 AWG (0.32 mm²) or 20 AWG (0.52 mm²) stranded tinned copper.
Cable Shielding: 100% Aluminum-Mylar foil wrap with 85% tinned copper braid drain wire.
Insulation Temperature Rating: PTFE/FEP insulated leads (-65°C to +200°C) for engine bays; PFA (-200°C to +260°C) for extreme exhaust zones.
Selecting the correct wire gauge is vital for maintaining balanced conductor impedance. While 24 AWG wire is physically easier to route through tight harnesses, its higher internal resistance per foot increases the risk of lead unbalance if crimps or screw terminals degrade over time. Manufacturer specs strongly recommend 22 AWG or 20 AWG stranded wire for runs exceeding 20 feet (6 meters).
Self-heating is another critical factor in voltage delivery. The electrical power dissipated by the sensing resistor element is defined by $P = I^2 R$. If a transmitter sends 5 mA of excitation current through a 100 Ω RTD, power dissipation reaches $P = (0.005)^2 \times 100 = 2.5\text{ mW}$. In still air or enclosed thermowells, 2.5 mW elevates the sensor core temperature above the surrounding medium, creating a false high reading. Professional instrumentation transmitters limit constant excitation current strictly to 1.0 mA or less ($P = 0.1\text{ mW}$).
Terminal Block Pin Assignment for 3 Wire Pt100 Transmitters
When wiring a 3 wire pt100 connection diagram into specialized equipment—such as Rosemount 3144P, Siemens SITRANS, Omron E5CC controllers, or MoTeC telemetry units—the physical pin assignment labeling on the terminal block varies significantly across manufacturers. Understanding these common terminal layouts ensures proper connectivity on the bench or shop floor.
| Transmitter / Controller Model | Terminal 1 (Primary / Hot Wire) | Terminal 2 (Return / Neutral Wire) | Terminal 3 (Compensation Lead) |
|---|---|---|---|
| Standard PID Controller (e.g., Omron, AutomationDirect) | Pin 1 or A (Red Lead) | Pin 2 or B (White Lead) | Pin 3 or B’ (White Lead) |
| Head-Mount 4-20mA Puck Transmitter | Terminal 3 (Red Lead) | Terminal 4 (White Lead) | Terminal 5 (White Lead / Jumper) |
| Rosemount / Emerson Field Transmitters | Terminal 1 (Sensor +) | Terminal 2 (Sensor -) | Terminal 3 (Compensation) |
| Automotive ECU / Data Acquisition Module | Ain+ / RTD Excitation | Ain- / Sensor Ground | Comp Ref / Sense Line |
Regardless of specific terminal labeling, the operational principle remains identical: the single red primary lead lands on the positive excitation terminal block, while the two white common leads land on the remaining signal ground and compensation terminals.
Common 3 Wire Pt100 Connection Diagram Wiring Errors and Fixes
Even small wiring errors can cause significant temperature offsets, erratic signal drift, or complete controller fault trips. Below are four common wiring mistakes, their physical symptoms, and exact troubleshooting diagnostic fixes.
1. Accidental Cross-Wiring of the Primary Excitation Lead
Symptom: Controller display reads extreme negative or positive values (e.g., -200°C or +850°C), or throws an “Open Sensor” error code.
Cause: The single primary wire (Red) was inadvertently wired into the compensation terminal block, while one of the return wires (White) was connected to the primary input terminal.
Diagnostic & Fix: Disconnect all sensor wires from the terminal block. Measure resistance across each pair using a DMM. Identify the isolated primary lead (Red), which shows ~108 Ω to either of the other two wires. Identify the two matching compensation leads (White), which register near 0 Ω between each other. Re-land the Red lead exclusively on Terminal A (S+).
2. Ground Loops Caused by Double-Ended Shield Termination
Symptom: The temperature reading spikes, fluctuates rapidly, or displays severe electrical noise when nearby electric motors, VFDs, or automotive ignition systems are energized.
Cause: The bare ground wire drain shield was connected to earth ground at both the sensor thermowell shell and the controller terminal block, forming a ground loop circuit that inducts stray AC electromagnetic noise into the signal lines.
Diagnostic & Fix: Disconnect the ground wire shield at the sensor head. Insulate the cut braid using heat-shrink tubing. Ensure the shield drain wire is grounded strictly at the instrument enclosure chassis terminal.
3. Unbalanced Lead Resistance Mismatch
Symptom: The temperature reading shows a constant offset error (e.g., consistently reading 3°C to 8°C higher or lower than actual fluid temperature) despite recalibration.
Cause: Mixing wire gauge sizes (e.g., using 20 AWG for the Red lead and 24 AWG for the White leads) or using a damaged screw terminal block with corrosion creates unequal resistance across the leads. The 3-wire bridge compensation formula relies on exact equality of lead resistance ($R_{\text{Lead1}} = R_{\text{Lead2}} = R_{\text{Lead3}}$).
Diagnostic & Fix: Measure loop resistance from the disconnect block. Measure Lead 1 resistance, Lead 2 resistance, and Lead 3 resistance independently. If resistance values differ by more than 0.2 Ω, replace the cable harness with a unified multi-conductor shielded cable constructed of uniform AWG gauge wire.
4. Controller Input Configuration Mismatch
Symptom: The wiring matches the diagram perfectly, but the temperature reading displays roughly 2.5 times higher than expected room temperature.
Cause: The controller’s internal software parameter is set to “Pt1000” or “Type K Thermocouple” instead of “3-Wire Pt100 (385 alpha)”.
Diagnostic & Fix: Navigate to the system setup menu on your controller or PLC input card. Verify that the sensor input type is configured specifically for Pt100 / 3-Wire / Alpha 0.00385.
3 Wire Pt100 Connection Diagram Frequently Asked Questions
What is the primary difference between 2-wire, 3-wire, and 4-wire Pt100 connection diagrams?
A 2-wire diagram connects single leads to each side of the RTD, making it simple but incapable of compensating for cable resistance (resulting in distance-based temperature drift). A 3-wire connection uses a third lead to form a compensation loop, eliminating lead wire resistance errors for most standard industrial and automotive applications. A 4-wire connection uses two dedicated current leads and two dedicated voltage-sense leads (true Kelvin sensing), completely eliminating all lead resistance effects. 4-wire configurations are primarily reserved for laboratory calibration standards and ultra-precise laboratory applications.
How do I test a 3-wire Pt100 sensor using a digital multimeter?
Set your digital multimeter to measure Resistance (Ohms, Ω). Touch the probes to the two identical common wires (typically White and White). The multimeter should read between 0.0 Ω and 0.5 Ω (measuring only the copper lead loop). Next, measure resistance between the single primary wire (Red) and either of the common wires (White). At standard room temperature (21°C / 70°F), the reading should measure approximately 108.4 Ω. If you measure an infinite reading ($\text{OL}$) or $0\,\Omega$ short across the Red-to-White leg, the internal platinum element is damaged and requires replacement.
Can I connect a 3-wire Pt100 sensor to a 2-wire terminal block controller?
Yes, a 3-wire Pt100 sensor can be wired into a 2-wire controller terminal block. To do so, land the single primary lead (Red) into Terminal 1 (S+). Twist the two common leads (White 1 and White 2) together and land them both into Terminal 2 (S-). Note that running a 3-wire sensor in a 2-wire configuration disables the active lead-wire resistance compensation feature, making the system susceptible to temperature offset errors caused by long cable runs.
Why is the shield ground wire connected on only one end of the RTD cable?
Connecting the bare ground wire braid or drain wire on both ends of an instrument cable creates a closed metallic path between two physically separated chassis ground points. If a potential difference exists between these ground points, ground loop current flows through the shield braid. This loop induces AC electromagnetic noise onto the microvolt-level temperature sensing lines. Grounding the shield braid exclusively at the controller chassis allows ambient EMI to drain safely to earth ground without inducing noise spikes into the RTD signal path.
What causes unexpected temperature drift on a 3-wire Pt100 circuit after installation?
Temperature drift in a properly wired 3-wire Pt100 circuit is usually caused by terminal block corrosion, mechanical strain on the lead crimps, moisture ingress inside the probe head junction, or excessive excitation current causing element self-heating. Inspect all screw terminal clamps to confirm tightness, check that wire gauge runs are fully symmetrical, and ensure moisture-proof IP67/IP68 sealing glands are torqued down at the sensor connection head.
Step-by-Step Guide to Understanding the 3 Wire Pt100 Connection Diagram
Identify – Determine the RTD lead configuration using a multimeter to measure resistance across wire pairs (100 ohms across element, ~0 ohms between common leads).
Locate – Find terminal blocks marked RTD, Pt100, or pins A, B, and C on your PID controller or temperature transmitter.
Reference – Consult the 3 wire pt100 connection diagram to match red (compensation/sense) and white (hot signal) leads to designated pin assignments.
Connect/Route – Terminate the two red wires into common compensation terminals (e.g., Pins 1 and 2) and white into Pin 3, routing away from heavy high-voltage hot wire runs.
Verify – Apply power and test resistance or temperature output against ambient baseline, ensuring screen displays ambient room temperature without offset errors.
Troubleshoot – If temperature reads high or open circuit, inspect terminal tightness, verify ground wire drain isolation, and check for reverse neutral wire or mismatched pin orientation.
