Stihl MS 311 Parts Diagram: Component Breakdown (2026)
The Stihl MS 311 parts diagram details the internal layout of this 59.0 cc engine chainsaw. It highlights major sub-assemblies including the cylinder kit, Walbro/Zama carburetor configuration, crankcase system, recoil starter, oil pump drive, and ignition module, enabling precise component identification and correct reassembly.
📌 Key Takeaways
- Engine displaced at 59.0 cc with a 47 mm cylinder bore diameter.
- Carburetor fuel lines require specific pulse hose routing to maintain crankcase vacuum pressure.
- Cylinder head bolts must be torqued in a cross-pattern to 11.5 Nm (8.5 ft-lbs).
- Impeller and oil pump worm gear wear are primary causes for chain lubrication failure.
- Seek professional service if crankcase sealing or crankshaft bearing replacement is needed.
The Stihl MS 311 mid-range chainsaw relies on a 59.0 cc 2-MIX engine architecture designed to provide high torque across a broad operating RPM band while reducing emissions. Performing precise maintenance, top-end overhauls, or crankcase splits on this powerhead requires an accurate reference to the official Stihl MS 311 parts diagram. This technical schematic breaks down the powerhead into modular assemblies, detailing structural geometry, fastener specifications, OEM part numbers, and interconnecting pathways. By understanding this internal layout, technicians can effectively trace fuel lines, map ignition circuitry, verify air filtration seals, and source correct replacement components for the 1140 series platform.

Stihl MS 311 Parts Diagram: Engine and Subsystem Component Breakdown
The Stihl MS 311 architecture is categorized under the Stihl 1140 engine chassis, which shares several structural traits with higher-displacement models in the same family. However, individual internal component specs remain distinct. Utilizing an exploded view allows mechanics to isolate primary systems and understand how sub-assemblies interface with the crankcase and composite handle frame.
Cylinder, Piston, and Powerhead Assembly
At the core of the MS 311 powerhead layout is the 47 mm bore cylinder mated to a 34 mm stroke crankshaft. According to OEM specifications, the cylinder features a wear-resistant Nikasil lining designed to handle high thermal loads. The piston assembly utilizes dual piston rings to maintain primary compression. When inspecting the engine blueprint, note that the cylinder bolts directly to the engine pan rather than utilizing a traditional two-piece crankcase split down the centerline. This engine shroud design requires precise sealant placement along the mating flange during rebuilds.
Fuel Induction, Air Filtration, and Carburetor System
The air intake system uses a pre-separation air filtration layout that centrifugally ejects heavier dust particles before reaching the main HD2 filter element. The carburetor (typically a Walbro WTE-10 or HD-41 series depending on production year) connects to the cylinder intake port via a flexible rubber manifold boot and an independent impulse hose. Proper routing of the impulse hose—which transfers crankcase pulse pressures to operate the carburetor fuel pump diaphragm—is critical for engine operation. Refer to our comprehensive chainsaw carburetor tuning guide for additional pressure adjustment protocols.
Ignition System and Flywheel Layout
The electrical configuration consists of a cast-aluminum flywheel equipped with cast-in rare earth magnets and a solid-state ignition module. The ignition module is mounted on the fan housing side of the crankcase, held by two M4 fasteners. The module must be set with an air gap of 0.2 mm to 0.3 mm (0.008 in to 0.012 in) relative to the flywheel pole shoes. The stop switch wire and ground lead route through molded channels in the tank housing to prevent chaffing against vibrating components.
Clutch, Drive Sprocket, and Automatic Oiling System
The drive system features an outwardly facing three-shoe centrifugal clutch threaded directly onto the M10x1 left-hand thread crankshaft stub. Positioned behind the clutch spider is the drive gear for the adjustable automatic oil pump. The oil pump picks up bar lubricant through a pickup body located inside the oil tank and feeds it through an internal channel to the guide bar mounting pad.
Always verify the 1140 series generation when ordering engine components. The Stihl MS 311 uses a 47 mm cylinder bore, whereas its larger family counterpart (MS 391) uses a 49 mm bore. Crankcase pans and engine shrouds are dimensionally similar, but piston and cylinder components are non-interchangeable.
| Assembly Group | Key OEM Reference Part Numbers | Fastener & Torque Specs |
|---|---|---|
| Cylinder & Piston Assembly (47 mm) | 1140 020 1200 / 1140 030 2000 | M5x20 Torx T27 (11.5 Nm / 8.5 ft-lbs) |
| Carburetor Assembly (Walbro WTE) | 1140 120 0600 | M5 Flange Nuts (3.5 Nm / 2.6 ft-lbs) |
| Ignition Module / Coil | 1140 400 1300 | M4x15 Torx T27 (4.5 Nm / 3.3 ft-lbs) |
| Centrifugal Clutch Assembly | 1140 160 2000 | M10x1 LH Thread (50.0 Nm / 36.8 ft-lbs) |
| Adjustable Oil Pump Assembly | 1140 640 3200 | M4x12 Torx T27 (4.0 Nm / 2.9 ft-lbs) |
Navigating the Stihl MS 311 Schematic Layout for Teardown and Rebuild

Working effectively with a Stihl MS 311 parts diagram requires a systematic approach to disassembly, component grouping, and torque management. Following proper procedural steps ensures that small hardware, seals, and routing clips are returned to OEM specs during reassembly.
Step 1: Mapping Fastener Locations and Applying Torque Specifications
Before loosening engine hardware, reference the schematic layout to identify screw types and length variations. Stihl heavily utilizes IS-P threads (self-tapping thread-forming screws into polymer) alongside standard metric threads into magnesium and aluminum. Torque values must strictly follow manufacturer guidelines to prevent stripping threads in polymer housings or warping sealing surfaces.
Step 2: Isolating Sealing Surfaces and Gasket Sets in the Configuration
The MS 311 does not rely on traditional paper crankcase gaskets. Instead, the lower engine pan seals to the upper cylinder casting using high-temperature liquid gasket sealant (such as Dirko HT or Stihl OEM sealant 0783 830 2000). Radial shaft seals on the flywheel and PTO sides press into pre-machined grooves. The diagram indicates exact seal orientation: the sealing lips must face inward toward the crankcase cavity, with radial spring bands intact.
Step 3: Verifying Sub-Assembly Interfaces and Serial Revision Changes
Over the production run of the 1140 chassis, minor component updates occurred regarding the air filter housing base, tank vent design, and rewind starter pawls. Always check your powerhead’s 9-digit serial number against the diagram updates to confirm whether your saw utilizes early-style or late-style intake manifold retainers and AV (anti-vibration) spring mounts.
Do not use impact drivers on cylinder screws or crankcase pan bolts. Cross-threading or over-torquing screws into the engine block can permanently damage the threads, causing catastrophic primary compression leaks. Use a calibrated torque wrench and T27 Torx driver bits.
Common Stihl MS 311 Parts Diagram Troubleshooting and Diagnostic Procedures

When an engine exhibits performance loss, erratic idling, or failure to oil the chain, the parts diagram acts as a diagnostic blueprint to trace mechanical faults back to specific components.
Diagnosing Air Leaks via Crankcase and Impulse Line Schematics
A lean running condition or high uncontrolled idle often indicates an unmetered air leak. By referencing the schematic, technicians can methodically test known leakage vectors. Primary failure locations include:
- Intake Boot Sealing Flange: Cracks in the rubber bellows or loose plastic securing collars.
- Impulse Hose (Part # 1140 141 8600): Dry rot or detachment at either the crankcase barb or carburetor flange.
- Crankshaft Radial Seals: Outer lip wear caused by debris ingress behind the clutch or flywheel.
- Engine Pan Sealing Bead: Breakdown of the liquid gasket seal due to thermal fatigue or loose engine pan bolts.
For detailed step-by-step seal replacement and pressure testing methodologies, refer to our two-stroke vacuum leak testing procedures guide.
Tracing Fuel Delivery Blockages and Tank Vent Faults
If the saw starts but starves for fuel under load, consult the fuel tank assembly blueprint. Inspect the pickup body (fuel filter) located in the tank, followed by the fuel line itself. The fuel line routes through a molded grommet hole in the chassis. If the line collapses or pinches, fuel flow is restricted. Additionally, verify that the active tank vent (Part # 0000 350 5800) opens correctly to relieve negative pressure inside the fuel cell as fuel is consumed.
Resolving Chain Lubrication Failures in the Oil Pump Drive
Lack of chain lubrication usually stems from a stripped oil pump drive gear. The oil pump drive gear features a plastic worm gear that engages with a notched drive spring on the clutch drum. As illustrated in the clutch section schematic, if the chain brake is engaged while the throttle is pinned, friction generates heat that can melt the plastic worm gear teeth, severing mechanical drive to the oil pump.
When conducting crankcase pressure and vacuum testing on the MS 311 powerhead, pressurize the crankcase to 0.5 bar (7.25 psi). The assembly must hold pressure for a minimum of 20 seconds without a drop exceeding 0.02 bar. Apply 0.5 bar of vacuum using the same parameters to test radial seal lip retention.
Stihl MS 311 Parts Diagram Questions and Maintenance Solutions
How do I identify the correct carburetor revision on my Stihl MS 311 schematic?
Check the stamped identification code located on the carburetor body, adjacent to the metering chamber cover. Most Stihl MS 311 units utilize a Walbro WTE series carburetor (such as the WTE-10). Match this code against the parts list sub-headings, as rebuild kits (diaphragms, gaskets, and needle valves) vary depending on whether the saw is equipped with standard or compensated intake housings.
What is the correct ignition coil air gap setting listed in the MS 311 blueprint?
The air gap between the ignition module poles and the flywheel magnets must be set to 0.2 mm to 0.3 mm (0.008 in to 0.012 in). To set this accurately during reassembly, loosen both module mounting screws, insert a non-magnetic feeler gauge (or OEM gauge shim 4118 890 6400) between the flywheel magnets and the module, allow the magnets to pull the coil inward, and torque the T27 fasteners to 4.5 Nm (3.3 ft-lbs).
Are Stihl MS 311 components interchangeable with the Stihl MS 391?
Many chassis, recoil, handle frame, and external component parts are identical between the MS 311 and MS 391 since both utilize the 1140 series platform. However, the top-end engine components differ. The MS 311 features a 47 mm cylinder bore with matching piston, whereas the MS 391 uses a 49 mm cylinder bore (giving it 64.1 cc displacement). For details on the larger engine setup, view our Stihl MS 391 engine overhaul specifications documentation.
How is the automatic chain oiler drive assembly configured on this model?
The oil pump is located on the right side of the crankcase behind the clutch spider assembly. It is driven mechanically by a drive wire arm that hooks into a notch on the clutch drum rim. As the clutch drum rotates during chain movement, it turns the worm gear shaft inside the oil pump housing. If the drive wire is bent or missing during a clutch replacement, the pump will not rotate, stopping oil flow to the bar.
Where is the tank vent located in the Stihl MS 311 fuel system layout?
The tank vent is positioned in the upper wall of the fuel tank housing, tucked beneath the rear handle shroud near the carburetor chamber. It consists of a barbed valve body containing internal umbrella or duckbill valves designed to let air enter the tank as fuel drops, preventing vacuum lock, while blocking fuel from leaking outward when the saw is operated on its side.
Step-by-Step Guide to Understanding the Stihl Ms 311 Parts Diagram
Identify – Identify the specific assembly section in the Stihl MS 311 parts diagram corresponding to your repair work.
Locate – Locate the individual OEM part numbers and exploded callout numbers matching your worn or damaged component.
Reference – Reference the structural layout and hardware configuration to understand the correct reassembly order and orientation.
Connect/Route – Route fuel lines, impulse hoses, and wiring harnesses according to the path designated in the diagram layout.
Verify – Verify critical specifications, including ignition coil air gap (0.3 mm) and fastener torque values before reassembly.
Troubleshoot – Troubleshoot binding components, vacuum leaks, or misaligned linkages by comparing physical placement against diagram views.
Stihl Ms 311 Parts Diagram: Frequently Asked Questions
What does the stihl ms 311 parts diagram show?
The Stihl MS 311 parts diagram displays exploded views of the 59.0 cc engine, fuel tank housing, ignition system, oil pump, and carburetor assemblies. It lists original OEM part numbers, hardware sizes, gasket configurations, and structural layouts needed for complete component identification and accurate repair sequencing.
How do I read the stihl ms 311 parts diagram?
Locate the primary sub-assembly group matching your repair task, such as the crankcase or recoil starter. Cross-reference numbered key callouts with the index table to find official OEM part descriptions and part numbers. Dotted lines indicate internal fitment structure, sub-assemblies, and hardware positioning.
What are the main components in stihl ms 311 parts diagram?
Key components include the 47 mm piston/cylinder assembly, Walbro HD-series carburetor system, air filter housing, recoil starter assembly, centrifugal clutch assembly, flywheel, ignition module, and oil pump mechanism. Understanding this structure helps ensure proper teardown, component alignment, and reassembly.
What are common problems with stihl ms 311 parts diagram?
Diagram users frequently encounter misidentification due to mid-production design revisions, such as variations in carburetor fuel lines or air filter configurations. Always check your saw’s serial number against the diagram index to ensure correct OEM replacement parts and sealing gasket layouts are selected.
Can I use stihl ms 311 parts diagram for DIY repair?
Yes, the diagram provides essential guidance for DIY repairs such as replacing carburetor diaphragms, drive sprockets, spark plugs, or recoil starter springs. However, complex bottom-end work like splitting crankcases or pressing crankshaft bearings requires specialized Stihl pullers and technical experience.
What tools do I need for stihl ms 311 parts diagram?
Standard servicing requires T27 Torx drivers, a spark plug wrench (19 mm), circlip pliers, a feeler gauge for ignition coil air gap setting (0.2–0.4 mm), and a calibrated torque wrench. Specialty repairs may require a Stihl flywheel puller and piston stop.
