The 2008 Toyota Highlander has a serpentine belt that drives the accessories. The belt is located under the hood on the passenger’s side. There is a diagram on the radiator support that shows the routing of the belt.
The belt should be replaced every 50,000 miles.
If you’re looking for a 2008 Toyota Highlander serpentine belt diagram, look no further! Here at Belt Diagrams we have all the diagrams you need to get your car back on the road in no time.
Whether you’re a do-it-yourselfer or a professional mechanic, our diagrams are easy to follow and will help you get the job done right.
Simply find the year, make and model of your vehicle in our database and we’ll show you the corresponding diagram.
Don’t waste any more time searching for that elusive serpentine belt diagram – come to Belt Diagrams and get it done right!
Credit: www.toyotanation.com
How Do You Change a Serpentine Belt on a 2008 Toyota Highlander?
Assuming you would like a blog-style answer to this question:
The serpentine belt on a 2008 Toyota Highlander can be changed by following these steps:
1. Park the vehicle on a level surface and set the emergency brake.
2. Lift up the hood and prop it open.
3. Locate the power steering pump, alternator, and air conditioning compressor. The serpentine belt will loop around these components.
4. Using a wrench or socket, loosen the bolts that secure the power steering pump, alternator, and air conditioning compressor to their respective brackets. Do not remove the bolts completely, just loosen them enough so that they can be moved slightly if necessary.
5. Carefully slip the old serpentine belt off of the pulleys and discard it.
6. Place the new serpentine belt around the pulleys making sure it is routed correctly according to your vehicle’s diagram (usually found on a sticker under the hood).
7 snugly but not too tightly) around each pulley until all are covered then lightly tug on each end ofthebelt to make sure it is tight against all ofthepulleys except fortheidlerpulley which should have slight tension againstit whenyoupushdownonthebelt between thatpulleyand another one nearby..
If it feels loose, gently tighten each bolt until there is no slack inthebelt then rechecktension as described above before moving onto step 8 below.,/li>8Onceyouareconfidentthebeltismountedcorrectlyandreacheditspropertensioning point as checked in step 7 above, finish tightening each bolt back down securely using your wrench or socket from step 4 until snug.,/li>9 Closehoodandtestdrivevehicletoverifycorrectfunctioningofthepowersteering pump,,alternator,,andairconditioningcompressorbeforereturningserviceto customer.
When Should the Timing Belt Be Replaced on a 2008 Toyota Highlander?
The timing belt on a 2008 Toyota Highlander should be replaced every 100,000 miles.
How Do You Change a Serpentine Belt on a Toyota Highlander?
Assuming you have the tools and knowledge to do so, changing a serpentine belt on a Toyota Highlander is not difficult. The process is as follows:
1. Park your Highlander on a level surface and set the emergency brake.
2. Open the hood and locate the engine’s drive belts. On the Highlander, these are located on the driver’s side of the engine bay.
3. Using a socket wrench or belt tensioner, loosen and remove the old serpentine belt from its pulleys.
4. Install the new belt by threading it around all of the appropriate pulleys in their proper order (refer to your owner’s manual for specific instructions).
5. Use your socket wrench or belt tensioner to tighten the new belt before closing up your engine compartment.
How Often Should Toyota Serpentine Belt Be Replaced?
The Toyota serpentine belt should be replaced every 60,000 to 100,000 miles.
2008 Toyota Highlander Serpentine Belt Replacement
2008 Toyota Highlander Serpentine Belt Replacement
If your 2008 Toyota Highlander is making a squealing noise, it may be time to replace the serpentine belt. This is a fairly easy do-it-yourself repair, and you can save yourself a lot of money by doing it yourself. Here’s how to replace the serpentine belt on your 2008 Toyota Highlander:
1. Park your Highlander and open the hood. Locate the engine air filter housing and remove the housing lid.
2. Rotate the tensioner pulley counterclockwise with a wrench or socket to relieve tension on the belt.
3. Remove the old belt from around the pulleys and discard it.
4. Wrap the new belt around all of the pulleys except for the tensioner pulley, and route it according to the diagram on the underside of the housing lid.
5. Rotate the tensioner pulley clockwise with a wrench or socket to apply tension to the new belt, then slip it onto the final pulley (the alternator).
Conclusion
If you’re looking for a 2008 Toyota Highlander serpentine belt diagram, you’ve come to the right place. At Toyota Parts Center we have a complete selection of genuine Toyota parts and accessories at wholesale prices. We also have helpful diagrams and illustrations to guide you through the process.
So whether you need a new serpentine belt or just want to see what one looks like, we can help.
