Msd 6Al Wiring Diagram Ford

MSD 6AL Wiring Diagram Ford – Installing the MSD 6AL Ignition Control Box. This is a digital programmable unit that will control timing and voltage output to the ignition system. It is important to read all instructions carefully before starting installation.

The most important thing to remember is that this box must be installed between the battery and the coil in order for it to work properly.

If you’re looking for a wiring diagram for your Ford’s MSD 6AL ignition system, you’ve come to the right place. Here at blog post, we’ve got all the information you need to get your ignition up and running in no time. First things first, let’s take a look at what an MSD 6AL is and does.

An MSD 6AL is an electronic ignition system that replaces your vehicle’s factory ignition system. It produces a high-energy spark that improves engine performance and fuel economy. Now that we know what it is, let’s get into the nitty gritty of how to wire it up.

First, you’ll need to disconnect the battery negative terminal before starting any work. Once that’s done, remove the old distributor cap and rotor (if applicable). Next, connect theMSD red wireto the positive (+) terminal on the coil, then connectthe black wireto ground (-).

Finally, installthe new distributor cap and rotor (if applicable), making sure that everything is tight and secure. That’s all there is to it! With your new MSD 6AL in place, you can enjoy improved engine performance and better fuel economy.

Msd 6Al Wiring Diagram Ford


How Do You Wire a Msd 6Al Box?

If you’re looking to upgrade your engine’s ignition system, the MSD 6AL box is a great choice. But how do you wire it up? Let’s take a look.

The first thing you’ll need to do is disconnect the battery. This is important for safety reasons, as you don’t want any live electrical current while you’re working. Next, locate the coil pack on your engine and remove the two wires going to it.

These will be replaced with the new wires from the MSD 6AL box. Now, take the red wire from the MSD 6AL box and connect it to the positive terminal on the battery. Then, take the black wire and connect it to ground.

Finally, take the remaining two wires from the coil pack and attach them to their respective terminals on the MSD 6AL box. That’s all there is to it!

What Color is the Tach Wire on Msd 6Al?

The tach wire on an MSD 6AL is usually green. If it is not, then it may be any other color except for brown or white.

What Does a Msd 6Al Ignition Box Do?

An MSD 6AL ignition box is a device that increases the voltage of your car’s ignition system, providing a hotter spark that can help to improve engine performance. The increased voltage also helps to reduce the likelihood of misfires and can make starting your car easier in cold weather.

Does a Msd 6Al Have a Rev Limiter?

No, the MSD 6AL does not have a rev limiter. However, it does have two rotary switches that allow you to select between two different rev limits. The first switch is for engine RPMs between 1,000 and 6,500, and the second switch is for engine RPMs between 6,500 and 8,000.

MSD Ignition Installation | MSD 6AL and MSD Distributor Installation and Wiring

Msd 6Al Instructions

If you’re looking to upgrade your engine’s ignition system, the MSD 6AL is a great option. Here are step-by-step instructions for installing this performance part. 1. Disconnect the negative battery cable and remove the stock coil wire from the distributor cap.

2. Unscrew the two screws that hold the module in place and remove it from the vehicle. 3. Connect the red wire from the MSD 6AL to the positive (+) terminal on the coil and connect the black wire to ground. 4. Place the MSD 6AL in the location where you removed the old module, making sure that all wires are clear of any moving parts.

Secure it in place with the two screws. 5. Reconnect your battery cable and start up your engine!


If you’re looking for a wiring diagram for a Ford MSD 6AL ignition system, you can find it here. This blog post provides a detailed explanation of the wiring diagram and what each wire does.

Show full profile


Robert is a lifelong enthusiast of all things automotive. He has been working with wiring diagrams and schematics since he was in high school, and continues to use them as the foundation for his knowledge today.

We will be happy to hear your thoughts

Leave a reply

Enable registration in settings - general
Shopping cart