The serpentine belt is located on the engine of the 2007 Acura TL. It is a long, flexible belt that helps to drive the accessories on the engine. The serpentine belt diagram can be found in the owner’s manual of the car.
If you need to replace the serpentine belt on your 2007 Acura TL, you’re in luck. The process is actually quite simple and can be done by most do-it-yourselfers. All you need is a new serpentine belt, a few tools, and about 30 minutes of free time.
To begin, open the hood and locate the power steering pump. You’ll see a pulley on the front of the pump with a small notch cut out of it. This is where you’ll insert a wrench or socket to loosen the tensioner pulley bolt.
Once loosened, rotate the tensioner counterclockwise until there’s enough slack in the belt to slip it off all of the pulleys.
Now simply remove the old belt and route the new one around all of the pulleys except for the power steering pump (which should still have your wrench or socket attached). Be sure to followthe diagram on your vehicle’s fan shroud so that you routethe belt correctly.
Finally, tighten downthe tensionerpulley bolt and voila! You’ve just replaced your own serpentine belt!
Credit: www.youcanic.com
How Do You Change a Serpentine Belt on a 2007 Acura Tl?
Assuming you have the right tools, it is a relatively easy process. You will need a socket wrench and an extension.
First, locate the serpentine belt tensioner.
It is on the passenger side of the engine, near the top. There is a small hole in the center of the pulley.
Insert the socket wrench into the hole and turn clockwise to release tension on the belt.
Then, using your other hand, pull the belt off of all of the pulleys except for the one on the tensioner pulley.
Next, rotate the tensioner pulley counterclockwise with your socket wrench until you can slip the new belt around it. Then, route the new belt around all ofthe other Pulleys EXCEPT forthe one onthe AC compressor (it has a black knob).
The routing order is as follows:
-Tensioner Pulley
-Idler Pulley (smallest diameter)
-Alternator Pulley (largest diameter)
How Do You Put a Serpentine Belt on a 2006 Acura Tl?
Assuming you don’t already know how to do this, here are detailed instructions:
1. Park your 2006 Acura TL on a level surface and set the emergency brake. Place a jack under the front of the car and raise it until the tires are off the ground.
2. Locate the serpentine belt routing diagram on the underside of the hood. This will show you how the belt should be routed around the pulleys.
3. Using a socket wrench, loosen but do not removethe bolts that hold the power steering pump in place.
You may need to adjustthe position ofthe pump in order to gain access tothe tensioner pulley behind it.
4. Insert a 3/8″ drive ratchet into the square hole in the tensioner pulley and turn it clockwise to release tension onthe belt. Carefullyremovethe old belt fromaround alloftheribbedpulleys except fortheidlerpulley (located at bottom center).
The newbeltcan nowbe installed byloopingit around allofthepulleys as shown inthe routing diagram-again, making surenot totouchanyofthe otherbeltsonthe vehicle!
Where is the Serpentine Belt Diagram?
Assuming you need the serpentine belt diagram for a specific car, the best place to find it would be in the owner’s manual. If you don’t have the owner’s manual, you can usually find the diagram on a sticker under the hood or on the radiator support.
How Do I Know If My Belt Tensioner Needs Replacing?
If your vehicle’s engine is equipped with a serpentine belt, it also has a belt tensioner. The purpose of the belt tensioner is to keep the proper tension on the serpentine belt so that it can turn the accessories pulleys properly. Over time, the bearing in the tensioner can wear out and cause noise or vibration.
If this happens, you’ll need to replace the tensioner.
Here are four signs that your belt tensioner needs to be replaced:
1. You Hear Noise Coming From The Engine Bay
If you hear squealing or grinding noises coming from under the hood, it’s likely that your belt tensioner is failing. The noise is usually caused by a worn-out bearing in the tensioner assembly. As the bearing wears out, it will start to make noise as it tries to spin freely inside the housing.
This noise will usually get worse as you drive and may even become constant at high speeds.
2. Your Serpentine Belt Is Slipping Off The Pulleys
If your serpentine belt starts slipping off its pulleys, it’s a good indication that your belt tensioner isn’t doing its job properly.
When this happens, you’ll typically see smoke coming from under the hood as well since the belts are now rubbing against other engine components. In some cases, this can also lead to an overheated engine since the belts aren’t able to cool down properly anymore. If you see either of these symptoms, pull over and call for roadside assistance immediately since driving any further could damage your engine beyond repair.
3. There’s An Oil Leak Coming From The Tensioner Assembly
It’s not uncommon for oil leaks to develop around the seal on the back ofthebelt tensionersassemblysinceit’s constantlyexposedto heatand moving parts insidetheengine bay..
Ifyou notice anoil leakcomingfromthebackofyourtensionersassembly,itneedstobereplacedimmediatelysinceitcouldleadto afailureofthepartandpossiblycauseanenginefire.. 4..TheTensionerPulleyIsWobbly Or Has Excessive Play In It Ifyou notice thatthepulleyonthetensionercanbe wiggledbackandforthorhas excessiveplayinitthenitisdefinitelyfailingandneeds toreplacedbeforeityouenduplosingyourserpentinebeltwhileyoudrive..
ACURA TL SERPENTINE BELT REPLACEMENT TUTORIAL
2007 Acura Tl Serpentine Belt Replacement
If your 2007 Acura TL is making a squealing noise, it may be time to replace the serpentine belt. This is a relatively easy do-it-yourself repair that can save you money. Here’s how to do it:
1. Park your Acura TL on a level surface and set the emergency brake. Remove the negative battery terminal cable to prevent electrical shorts.
2. Place a drain pan under the power steering pump to catch any fluid that may leak out when you remove the old belt.
3. Locate the tensioner pulley near the alternator and use a wrench or socket to loosen the tensioner nut counterclockwise. This will relieve pressure on the old belt so you can remove it easily.
4. Slip the new serpentine belt around all of the pulleys except for the tensioner pulley, then route it around the tensioner pulley last.
Use a wrench or socket to tighten the tensioner nut clockwise until there is no slack in the new belt, then double check that all of the other pulleys are still properly aligned before reattaching the negative battery cable terminal.
2007 Acura Tl Serpentine Belt Tensioner
If your 2007 Acura TL is making a squealing noise, it may be time to replace the serpentine belt tensioner. This is a relatively simple process that can be completed in about an hour.
First, locate the tensioner pulley near the front of the engine.
The Serpentine belt will be routed around this pulley. Using a socket wrench, loosen the bolt that secures the pulley in place.
Next, use a ratchet to loosen the nut that secures the tensioner assembly to the engine block.
With both of these nuts loosened, you should be able to slide the old serpentine belt off of the pulleys.
Now it’s time to install the new serpentine belt. Route it around all of the pulleys except for the tensioner pulley.
Now rotate the tensioner clockwise with your socket wrench until there is enough slack in the belt to slip it over onto the tensioner pulley.
Finally, tighten both bolts securely and start up your engine to test things out!
2008 Acura Tl Serpentine Belt Tensioner
If you’re like most car owners, you probably don’t think much about your serpentine belt tensioner. But this small, relatively inexpensive part plays a big role in keeping your engine running smoothly. Here’s what you need to know about Serpentine Belt Tensioners:
What is a serpentine belt tensioner?
A serpentine belt tensioner is a pulley that mounts on the engine and keeps the serpentine belt tight as it spins. The tensioner applies pressure to the belt so that it doesn’t slip off the pulleys.
Why do I need a serpentine belt tensioner?
A loose serpentine belt can cause all sorts of problems. It can cause your engine to overheat, because the water pump isn’t being driven properly.
It can also damage other parts of your engine, like the alternator or power steering pump. In short, it’s important to keep that belt tight!
How do I know if my serpentine belt tensioner needs to be replaced?
There are a few signs that your serpentine belt tensioner might need to be replaced:
You hear squealing when you start up your car – this could be caused by a loosebelt or worn-out bearings in the pulley.
Your car’s performance feels sluggish – if your car isn’t accelerating as quicklyas it should be, it could be due to a slippingbelt.
The check engine light is on – this could indicate any number of problems withyour vehicle, but it’s worth checking out nonetheless.
Conclusion
If your 2007 Acura TL is making a loud squealing noise, it’s likely due to a problem with the serpentine belt. This blog post provides a detailed diagram of where to find the serpentine belt on your Acura TL, as well as instructions for how to replace it.
